1. Introduction to Sensitive and Full Tone Programs
Introduces the XP Deus 2 programs two and three, comparing the Sensitive program to Deus 1 Fast and Sensitive Full Tone to the Hot program, including their discrimination settings.
hello there thank you for joining me and welcome to the xp deus 2 factory program series and today we're going to be talking about programs two and three sensitive and sensitive full tone
now if i was to compare the sensitive program with the deus one it would indeed be the deus fast program very similar characteristics but of course the sensitive program uses fast multi-frequency and also there's some notch enabled toslightly eliminate the signals from troublesome coke now moving on to the sensitive full-time program that's very much like the hot program on the deus 1.again it's got some notch enabled and a minus 6.4 discrimination so there's absolutely no iron rejection on this program we're relying on the tones to give us all the information we need so let's go on to our statictest target and let you hear what the sensitive and the sensitive full tone programs sound like now this targets georgia fifth six bunch buried at about nine inches deep now these differ very slightly as i said earlier thesensitive is very similar to the deus one day as fast the sensitive full tones is almost the same as the hot program on the deus 1.
sensitive uses a 6.8 discrimination sensitive full tones uses a minor 6.4 discrimination so it's wide open there's no discrimination at all but we're relying on the tones to discriminate the target well actually we're relying on the tones togive us an identification of the target so okay let's go over george with the sensitive program first and see what it sounds like
2. Testing Sensitive Program and Sensitivity Adjustments
Demonstrates the Sensitive program on a buried sixpence, then adjusts sensitivity and performs a noise cancel, finding 95 gives extra depth without excessive EMI chirping.
a lovely sweet two-way signal and once again referring back to the general program you can adjust those tones to suit your hearing now let's just have a tweak around here and see if we can make adjustments to thiswe've got the reactivity at 2.5 which i think is doing a pretty good job for this ground we've got the sensitivity which is at 90.now i think we could probably push this sensitivity a little bit more so let's raise the sensitivity up and see what happens we're at 95 now 98 now and we're getting a little bit of emi chirping can youhear that now a top tip here is to do a noise cancel because if you do a noise cancel for a clean emi channel you might be able to push that sensitivity a couple more notches so here wego let's press and hold the gb button and do a noise cancel it's an automatic noise cancel and you can see it running through there
that's all done now so i don't think making changes to that noise cancel made any difference it's it's a little bit chirpy still so i think 98 is a little bit too high for this particular environment so i'mgoing to stick to 95 so let's try sensitivity 95.
that's given me about an inch and a half extra depth on this target so raising your sensitivity does make a difference but don't push it too far because it will punish you so let's now go on to sensitive
3. Full Tone Audio and Audio Response Explained
Explains the sliding scale of full tone audio, demonstrates the high tone on the silver target, and shows how sensitivity and audio response adjustments affect signal loudness and depth perception.
full tones using the full tone audio now for those of you who don't know about the full tone audio it's on a sliding scale so the low conductivity targets and the iron come in as a low tone andit's on a sliding scale up until the high conductive targets where this six months here is indeed a high conductive target so i'd be expecting a high tone so let's let you hear what it sounds like
and there you go it's a nice smooth almost like a cat meowing sound isn't it once again the target id is exactly the same as the other programs 82 so can we make any adjustments to the sensitive fulltone program well we can't go lower on the discrimination but we can go higher on the sensitivity it's at 90.let's go to 95 because we know that's the sweet spot sensitivity 95.
once again we've got an extra one and a half inches on that target any other changes we can make we can change the audio response to bring that target closer we can make it a little bit louder solet's go from audio response 4 to audio response 6 and listen to it now
now audio response doesn't give you any more depth but it makes the signals louder the audio response if it's set low will give you a quiet sound for small and deep targets and a loud sound for shallow orlarge targets so you can get a good perception of depth regarding the audio response we've got lots of videos on that subject so if you have a look on the xp website you'll see more information so that's youraudio response and i don't think there's anything else we can do to really push this sensitive full-time program it is what it is and it's working really well over this particular target the sensitive full tone program uses thefull tone audio which is an excellent choice for searching in amongst iron what you're listening for is a high-pitched tone in amongst the low grumbles and this is also great for park hunting when searching for silver coins because
the silver coins really sing out loud
4. Cherry Picking High Conductive Targets
Introduces the cherry picking technique for targeting high conductive finds, then listens to two low conductive targets and one high conductive target to compare their tones.
and that's what you're looking out for i very often use the full tone program where i'm specifically looking for the higher conductive targets we call it cherry picking now in front of me here i've got two low conductivetargets and somewhere around there a high conductive target i'll let you listen to them
that's our first target and it's coming up at about 58 something like that quite a low tone isn't it and the second target's just hereand that's coming up at 51 so these two targets are very similar in tone and conductivity
now our third target is a screamer it's coming up at 91 and that's a high conductive target so for example if i was looking for just the big silver or the chunky targets i would ignore these two targetsand just dig the high conductive target but we're not going to ignore them let's dig them out let's go to the target number one
5. Digging Targets and Medieval Pendant Find
Digs the low conductive targets revealing small pieces of lead, then recovers the high conductive target, a medieval heraldic pendant, showing the value of full tone audio.
the low conductive target could well be trash
i don't think this is very deep
so there is a small piece of lead
coming in with a low tone okay let's go and check the next one
again a low tone could even be the same sort of target
a little bit deeper this one i think
and that's what it is again is another small piece of leadokay let's see what that high tone is now that high conductive target
loud one oh look at that i know what that what that is that's your high conductive target that is a medieval heraldic pendant that's a really cool find so if you wanted to cherry pick the good stuff thehigh conductors you can use a full tone audio