Transcript

Use with ChatGPT / Claude Auto-scroll A

1. Muffler Removal and Inspection

The host disassembles the muffler on a Vevor 72cc X-Torq clone saw, discovering restrictive exhaust ports and checking the cylinder cross-hatching through the spark plug hole.

0:00 - 0:24
Okay, here's the VR 72 cc X-Torq, I guess is what it's a replica of or a clone of.Uh but try to take some stuff apart and see what things are like.First, I'll do the muffler and see what the muffler looks like.
I probably should have power bits here.Make this faster, but you'll have to bear with me.
I don't know how to fast forward nothing either.I'm not an editor.Maybe one day I'll look into it, but as of right now, it is what it is.
Bought some cheap Amazon dogs that haven't come yet, but might have to modify them to fit, but I'm going to try some different dogs out.Dogs that come with it seem what we'll have you to seem pretty pathetic.
All right, so there must be more in there somewhere, huh?Or is it just stuck?I thought that would be it.
Mhm.Must be more.More screws someplace that I'm not seeing.
Well, let me go ahead and take top off, see if there's any other screws in there.
So, let's see here.That off.That off.Cover off.
I already took some of these screws out, but
4:30 - 4:39
Here I stop here for a bit and get a flashlight.Okay, so
I thought those were Never even paid attention, but I thought these two were exhaust ports and this was something another one, but those are just uh holes going back into the muffler screws.They have nothing to do with the exhaust outlets, so yeah, that's probably a pretty restricted probably pretty restricted
Uh see if I can break them loose.Looks like they're anumber five.
6:02 - 6:16
Mhm, wasn't too tight that one anyways.By the way, you should always go through your machines new machines and tighten first and figure out later.
But it's always exciting to get something new so you just go out and play with it.
Should have known when them short shorter screws came out of that front face, I should have known that what didn't bolt to the cylinder.Just not thinking, I guess.
I don't know whether you guys will be able to see in there if you have any nuts.No.
See if I can shine this light in there.
But it's uh
Yeah, there's no way I'm going to get you guys to be able to look in there.But uh there's literally nothing in there but There's nothing in there but that's the only outlet, so I don't know where else this is pretty restrictive.I mean, saw does cut pretty good but I have to look into modifying stuff or whatever.
I need like a smaller flashlight, I guess.
Again, there's probably no way I'm going to be able to get you guys to see in there but
And but
I don't see nothing too terrible yet, so might be some kind of little line there I'm seeing, but
I should take spark plug out and look down easier.
I'm looking on the back wall with the piston down and see there's still a lot of a lot of cross hatching and nothing major, so she must still be doing all right.
Pull the spark plug out.
And uh yes, I'm going to stop that video and then restart it and then we'll we'll go into the carburetor area after this.

2. Exploring the Carburetor and Intake System

The host removes the carburetor and intake components to examine the X-Torq design, then performs a compression test (around 170 psi) and reassembles everything.

All right, let's uh see what the carburetor and I've been kind of watching YouTube videos.I I never knew about the X-TorqHuskies or whatever.I never knew nothing about them.I got all older crap, so this is kind of all new to me.Um
11:35 - 11:38
And out.
And that goes on top.
And another hose don't want to come off.
Let's see if I can
I can get this guy off.
13:35 - 13:39
Uh, cable pops out pretty easy actually.
I wish I had you guys over there to show you that.
Well, seems amazing that whatever boot is on.So, I got maybe there's something wrong, but I don't know.Seems loose to me.We'll see when I get in there.
All right.This bottom here hangs onto the hose coming across this little thing, so I'll try to see if I can get them out of there and get this out of the way.
There's that side out.Get this guy out.
I don't know if that side went back in.
There it goes.Hopefully I pulled it out of the thing.It'll go back in, but got that little guy.Let's get that old diverter thing in there.
I don't know if I want to take that off.
So, it's looking like it's definitely not just some of the stuff.It's totally after the old X torch.
Yeah, I'm going to stop there for a bit.So, I just seen the battery is about dead on my camera.So, swap batteries and go from there.All right, let's try see if we can take this other part off.Well, that ain't thoroughly answered any questions, but as far as the style and design
Yeah, I think I'm not going to mess with that till I need to sometime.Man, that's pretty much
19:38 - 19:52
Yeah, it's looking pretty much it is the the X-Torq design, so yes.So, I need to get in there.This is good to go.Just kind of wanted to
do a video on kind of looking over the intake system.It's
20:08 - 20:20
the X-Torq.Not familiar with them at all, but I'll probably be learning.
20:28 - 20:35
All right.I'll I'm going to shut you guys off again.You don't need to see the reassembly of this.
Give it a compression test.I don't know how well you guys can see that, but
it's too hard to film trying to do it.
Looks like 150 60 70 170 compression.Watched one video a so that's not That's pretty good.That's the sweet spot, so.All right.Now I'll put the muffler back on and I'll go on to something else.All right.Got muffler back on, carburetor, and intake all back on.

3. Starter Mechanism and Clutch Check

With the muffler and carb back on, the host inspects the starter mechanism, noting rope wear and a tight spot, then examines the 3/8 7-tooth clutch and sprocket setup.

Uh let's take the side cover off and see what the how the starter mech- Oh, it wasn't too tight.Starter mechanism.I had a little more snug to it.Yeah, it was well snug, but not tight.Yeah, I don't know.I might have screwed up stuff taking it apart, who knows, but if nothing else, I got tighter bolts than I had.Muffler bolts were all just They were tight snug, but they weren't tight.
Which one did I first
Damn, yeah.
23:21 - 23:27
There's the stirring everything looks like.
See some phrase getting in the rope already.That could tight spot right there.
24:14 - 24:17
I shouldn't be doing this with the screwdriver.
There's a little spot where it wants to climb.It's like the gaps too.Close.
I'll deal with that at a later date.
All right.I'll put this back together.
All right.I will see what it looks like the clutch here.Let's see if I can keep from losing this thing.
All right, almost took it off.
And damn, don't focus good enough, does it?
Yeah, I don't focus up that close, so.Anyway, it's a 3/8 7-tooth.
Oh, good.Set the brake back.
27:26 - 27:38
So, that there the landing gear is in the arm to drive the clutch.
27:56 - 28:05
I got these are to get in than my old piece of that just that old wire piece on the both of my old Huskys.
Yeah, I can't do this without losing it.
Looks like I got it.
Yeah, it spins around the so we got that.
All right.Now, I guess I'll try to start it without the bar.

4. First Start and Cracked Brake Handle

The host attempts to start the saw without the bar and discusses audio issues, then reveals a crack in the flimsy plastic brake handle and his unsatisfying exchange with Vevor support.

Go back to zoom.Back out a ways.
Hopefully everything's all right.
Turn that on.I had pulled it over a bunch with the switch off, so see what happens here.
Yeah, I don't know what kind of I don't know what kind of mic cover thing to get or something, I don't know.Or now it seems like I record this, it sounds bad on film, but sounds good in person.
All right, so that was
That was kind of a partial teardown, kind of got to looking at still runs, didn't break nothing.Uh oh, one other thing I'm going to show is So, we got this out.And when I first got it, I thought, man, that's some flimsy plastic.And I didn't notice that for a while, but I don't know.See that crack right there?So, I have to get a new one of them brake things.I contacted Vevor.And they they said they'd send a free shipping, but I'd have to send that thing back the whole thing back, and then they'd give me my full refund.But I was like, well, that ain't a big enough deal to me to send it back, so.All right.Well, I'll see how this video goes.
This was something else I was going to take a look at, so.

5. Diagnosing Stiff Chain Tensioner

The host tears into the side chain tensioner that has been binding, finds excessive pressure grinding a bushing into the housing, and cleans and re-greases it to improve operation.

This here side screw thing, like it's
31:39 - 31:51
been fighting me the whole time.It's pretty stiff, so I'm going to see if I can take it apart.Right there, this I don't know
where it's binding up, but something's stiffening.So, I'm going to see about taking this apart.See if I can seesomething not lining up or something.
32:52 - 33:02
Well, it had grease in it, so Oh, there's like a bushing there.I don't know why that was
33:02 - 33:11
fighting so hard.It's kind of wonder if it was this area, but that feels loose now that there ain't no pressure on it.
And now even that seems kind of on the stiff side, so this is kind of a weird grease.I think I'm going to grab some cleaner, clean it up, so I'm going to go away for a bit.Put some dirt grease.While cleaning up,you can see this area right here is all
shiny.I think what's happening is that got
34:58 - 36:12
too much pressure on it from that piece that clamps it down.It's grinding into the housing.I think that's what's making it stiff.So, I'll continue to uh clean up and figure outgrease it and see if I can if it needs some kind of spacer or something, so that it ain't so bound up.It's got a little rubber O-ring there.Can't see it in the video there, but let's see what happens after I clean everything up, put a different grease in there, and I think I'm going to have to stand off that thing there, so it ain't gotso much pressure that way with the gear.Yeah, it seems to be better, but I had it running back and forth a bunch of times with the drill with the screwdriver bit in it, but yeah, there it's still not perfect, though.Getting late.I'm going to go in here pretty quick, so
I call this uh I'll work on another day, but don't know if this is putting too much pressure.Really ain't don't really have pressure.I don't know.Definitely is not not a smoothtightener on it.
All right, so

6. Fitting the Oregon Bar and Wrap-Up

The host fits a 32-inch Oregon bar from his XP 266 onto the saw, notes the bar cut crooked and needs reshaping, and plans to test it on a big cut in a future video.

There's with my 32-in
Oregon bar that was on my XP 266.So seems to fit.I haven't started it up yet, but see what happens, I guess.
Put some stuff away here.
38:18 - 38:46
The bar was cutting crooked, so that's why it was off my 266, but I'm going to get it reshaped up cuz I think it's still a good bar, but maybe I'll try to cut with it tomorrow if Igot time.On that big one and try this with a long bar and see what it does to that big block on my other video.All right.That's it for this time.
Seek backward 5s ←
Longer seek (10s) Shift ←
Play Space Seek forward 5s →
Longer seek (10s) Shift →
0:00 Auto-scroll A Copy link at current time S

Vevor 72cc XTorq