Transcript

Use with ChatGPT / Claude Auto-scroll A

1. Why the New Turntable Matters

The speaker revisits a previous cartridge analysis and explains how new tonearm adjustments became possible. He introduces the new Thorens TD 125 and why it is important for getting the setup right.

0:00 - 0:51
A few weeks ago, I published a a video about my experience with Walley Tools from Wham Engineering.And at the time, they had performed or JR Boy Clair and and Walley Tools had performed a an analysis of my cartridge to, you know, to to check out its, you know, the stylist rake angle and and thingslike that.And they provided me with a corrective shim.So I talked about that in the last video, my experience with that.Now, I'm very familiar with using the Walley tractor and the Walley skater.I've used them for two or three years now.They also sent me the Walley reference kit.And it revealed some things about my tone arm that I didn't know.And one was the azimuth was off.And also the vertical tracking angle was off.Now, the tone arm I had didn't allow for either adjustment.
But that's changed and that's what I want to talk about today.

2. Unboxing and Preparing the TD 125

He describes bringing home the Thorens TD 125, its Syrinx tonearm, and the ability to adjust speed and geometry. He also explains why he wanted time to learn the new table and carefully set it up with his Hana cartridge.

Yes, that's an empty turntable shelf.Now, this is my Thorens TD 160 all packed up and ready to go back to Dave at Vinyl Nirvana.I bought this turntable from Dave about Well, it was four years ago.It was it was 2022 that I ordered and purchased this turntable and Dave put it together.It's a reproduction Thorens TD 160 Super.Now, this past weekend, Mandy and I drove to Dave's to pick up a Thorens TD 125.I was very excited to get this turntable.It comes equipped with a Syrinx TA-1 tone arm, which allows for those adjustments that I couldn't do with my previous tone arm.And and that previous tone arm, by the way, was a a Rega RB 880.Now, the Syrinx allows me to to make those adjustments.So I couldn't wait to get started.Now, one of the the other things that I was excited about for with this turntable was the ability to adjust for speed.
So you can adjust the speed on this turntable.And I'm telling you, it is built like a tank.So when we got home, I asked Mandy, I said, hey, can I just have a few hours to to set this up.I was keeping my Hana MH cartridge.I wanted to use every Wally tool at my disposal to make sure it was as close to perfect as I could get it.And to do so, you really need to to spend the time with, you know, with the cartridge and the tone arm.And And plus, it's a new turntable for me.So, I wanted to learn the turntable and I wanted to learn that tone arm.So, I wanted to spend time setting it up.

3. Leveling and Azimuth Adjustments

The speaker walks through using the Wally Reference tools to establish a level starting point and correct stylus rake angle and azimuth. He emphasizes how the new tonearm let him fix a long-standing left-channel sibilance problem.

The first tool I used was the Wally Reference Dual Axis Blade.And you also need to use this in conjunction with shims that equal the height of your cartridge.And you can you can measure this.And in my case, I think it was like 17.25.So, I had to add shims or, you know, to to equal the height of my cartridge when I set this up.And the Dual Axis Blade allows me to make sure that the head shell is level with the record surface from front to back.Now, these directions affect different aspects of cartridge alignment.The the front to back tilt influences stylus rake angle or SRA and the vertical tracking angle or VTA, while the side-to-side tilt kind of influences azimuth.Not kind of, it does.Now, by establishing a level starting point, I now have a reference for making the more precise measurements and adjustments later.
And fortunately, like I said, the Sorbothane tone arm allows me to make adjustments to the tone arm's height, which is crucial.It was then on to the Wally Reference front-to-back tool.Now, this is to check the stylus rake angle.An incorrect SRA can increase distortion and it can also affect high frequency reproduction.The blade allows us to establish a measurable angle rather than just, you know, relying on visually, you know, judging whether the tone arm is parallel to the record.Now, if the SRA isn't correct, the stylus may not trace the groove as accurately as it should.Now, I do want to point out that that the blade doesn't exactly measure the stylus rake angle.It measures the head shells angle which you can then adjust.And next, I used the Wally reference left to right.I loved this one because this one's all about azimuth.
And this one actually pointed out a problem I had with my previous tone arm.And with that previous tone arm, I was experiencing sibilance in the left channel.And I had been I went I had been battling that for I can't tell you how long.And I never realized it was an azimuth problem.Thought it was all kinds of things, you know.I thought it was anti-skate.I thought it was, you know, speaker alignment.I can't even begin to to get into how long I was battling that.And little did I know it was azimuth.So this blade allows me to see exactly how much the head shell is tilted from one side to the other rather than, you know, guessing by looking at the cartridge.I can establish now a precise reference and make adjustments from there.Now out of all the adjustments that I made with those few hours that gave me to play around with this, I spent the most time with that, you know, that left to right to adjust for azimuth.
And the Soroane's head shell, the head shell that comes with the Soroane tone arm, has an azimuth adjustment screw.So I was able to to continuously adjust that to get it perfect or as perfect as you can, you know, humanly get.So I played around with that for maybe 20 25 minutes before I knew that I had it where I wanted it to be.

4. Final Cartridge Alignment Steps

He finishes the setup by balancing the tonearm, setting tracking force, aligning the cartridge with the Wally tractor, and dialing in zenith and anti-skate. He concludes that the turntable and tools helped him achieve very precise alignment.

And then it was time to screw the Hana into the head shell, adjust for alignment, zenith and anti-skate.But first I had to balance the tone arm and and then set the vertical tracking force, which in this case the the recommended tracking force for the Hana is 2 g.Now I use Baerwald alignment.And to nail this, I pulled out my trusty Wally tractor.But first I wanted to verify the arc that I was going to align it to on the tool.And now I know the effective length of the Soroane is provided by the manufacturer, but I wanted to make sure that the pivot to spindle distance was exactly where it should be.So I then popped the numbers into the online Wally calculator to determine the arc I needed to use.Now, I think this could be the most important tool in the in the whole toolkit, but I could argue that that, you know, Wally reference one that revealed, you know, the the side-to-side one that revealed my azimuth issue
might come in a close second.The Wally tractor allows you to nail the, you know, the horizontal alignment of your cartridge.And there are two things I'm adjusting here, overhang, which determines how far the stylus extends beyond this spindle, and also offset angle, which determines how the cartridge is rotated in the head shell.And since the tonearm moves across the record in an arc, the stylus can't remain perfectly aligned with the groove throughout the entire record.So the Wally tractor helps minimize that tracking error.It will help reduce distortion and allow the stylus to follow the groove more accurately.What I really like about the Wally tractor is the fact that it has a mirrored surface and which makes it easy to align the cantilever itself rather than relying on the cartridge body.And it's extremely satisfying when everything lines up.The Wally tractor itself does have zenith adjustment lines on it, but the analysis JR did meant I could use the Wally zenith to compensate for zenith error.
The Wally zenith allows me to make you know, really small adjustments to the cartridge's angle to compensate for any kind of zenith error.And the goal here is to get the actual contact surfaces of the stylus properly oriented to the record groove.And again, the goal here is to minimize distortion and allow the stylus to retrieve as much information as possible.And once I had all that down, I went back to the Wally tractor just for a moment to make sure that I hadn't thrown anything off while adjusting for zenith error.And then it was time to set the anti-skate.Now, I know a lot of manuals and even, you know, people will tell you to set the anti-skate to a number that's equal to your vertical tracking force.So in this case, mine is 2 g.So if I follow those instructions, I'll set my anti-skate to 2.
But that's not always correct.You'll be lucky if it does, if it if it actually is the the proper anti-skate to set it to.So the WallyScale kind of takes that guesswork out of it and then you can with confidence rest assured that everything is set up correctly.Now the WallyScale is awesome too because it it actually measures the amount of force on the tonearm.So when you do set it you can you can actually see how much you need to adjust just by just by following the instructions.It was a lot of work to be honest, but if you have the time like I said I put aside those those few hours, I actually enjoyed it.It was it was very relaxing and I went into it, you know, with a little bit of trepidation because you do want to get everything just right and it was a new turntable.
Actually you can see it it's right behind me.This is the turntable, the TD 1 25.So I was learning a turntable, I was learning the tools, and I can safely say that I am as close to perfect alignment as I could possibly get.

5. Closing Thoughts and Newsletter

The speaker thanks viewers for watching and reflects on the time and effort involved in the setup. He then mentions his free newsletter and signs off.

Now I want to thank you for watching.I really appreciate the fact that you're here.It means a lot to me because you could be doing so many other things than watching this.So I have a newsletter.I should mention that.The newsletter is free to join.There's a link in the description to, you know, to to join it.Comes out once a week.So until next time, please take care of yourself and enjoy your records.I'll see you soon.
Seek backward 5s ←
Longer seek (10s) Shift ←
Play Space Seek forward 5s →
Longer seek (10s) Shift →
0:00 Auto-scroll A Copy link at current time S

Same Cartridge, New Turntable: Can WallyTools Help?