1. The Search for the Ideal Shop Bit Driver
The speaker compares EDC bit drivers, multi-bit screwdrivers, and standard screwdrivers, outlining the tradeoffs of each and the goal of finding a setup with minimal downsides.
I've spent years trying to figure out the smallest and lightest EDC tools, like this bit driver from OITE.But what's the most comfortable and efficient bit driver you can get for the shop when you're not that tight on space?Something like the Vera Tool Check Plus is super space efficient, but it takes a fair amount of time to take out the bit driver and find the right bit.The driver is also really short and small in your hand, so you usually need to upgrade to a better driver.A standard multi-bit screwdriver is a bit more efficient because you can leave a commonly used bit like a Phillips number two in it so you can grab it and start working.But there's always a bit of wobble from the magnetic retention and the bulkiness of the bit holder means you can't reach recess screws.So you need to carry a separate precision driver for smaller size fasteners.
The gold standard for a bit driver is well a standard screwdriver because it's easy to grab and go.There's no fiddling around with bits.It also has no wobble because there's no moving pieces.It has a nice long blade for good reach.And most importantly, the blade is only as thick as the tip, so smaller screwdrivers are thinner and can act more like a precision driver.That's why I keep this set of VHA screwdrivers at the top of my tool chest for quick access.But screwdrivers have some big downsides.Since you need a separate screwdriver for each bit if you want to work on a wide range of sizes of Phillips, slotted, Torx, hex, and square fasteners, you'll end up with dozens of screwdrivers to carry around.I wondered if I could find a setup that minimized the downsides of a bit driver, but still avoids the need for a huge set of individual screwdrivers.
2. Wera Centrafix with Long Power Blades
Discovering the Wiha Centrafix's wobble-free locking mechanism and pairing it with 90mm Wiha power blades to create a driver that matches a standard screwdriver and reaches precision territory.
My favorite bit holder by far is the VHA centrifix because it is a locking mechanism that grips any kind of bit perfectly.So, it's 100% wobble-free just like a regular screwdriver.Problem is, this has a very short shaft.So, if you use a standard insert bit from the tool check plus, it's really stubby.Adding an extender gives me a bit more reach, but it reintroduces the wobble and the thicker collar on the extension means it won't fit into recessed holes like a regular screwdriver can.I found this longer Phillips number two bit floating around and started leaving it in the centrifix because it gave me a bit more reach and I could get right to work.Now, the problem with this is it's still quite a bit shorter than a standard Phillips number two screwdriver.So, I started looking around to see if I could find a longer set of bits that I could use.
Eventually, I found these VHop power blades that are perfect.They're 90 mm or 3 and 12 in long and are sold in sets so you can pick and choose what you want.The Phillips bit set comes with a 0, 1, 2, and three.And the slotted kit comes with 2 and 1/2, 3, 4 and 1/2, 5 1/2, and 6 mm.And the quality of these bits is excellent because VHA makes some of the best bits out there.And best of all, when you put them into the Centrifix, now you have something that is pretty much identical to a standard screwdriver in terms of its size, weight, length, and blade thickness.Now, this difference is even more pronounced when you put in a small bit.Swapping in the Phillips number one blade, we end up with something that's actually a little bit better than the standard screwdriver.
This has a little more reach and the blade is quite a bit thinner.And that's really the magic of using these power blades.In fact, if we swap in the Philips zero blade, now we're in precision driver territory.So, this can reach into the same spots that this Vera precision driver can reach into.So, the really cool thing here is that you end up with one driver handle and set of blades that will cover both precision bit and standard bit territory.
3. Organizing Bits with PB Swiss Blocks
Building a complete kit with security Torx, hex, and square bit sets, organizing all 29 blades into PB Swiss bit blocks, and comparing the setup to the Tool Check Plus.
As far as organization goes, if you try using one of these standard bit holder blocks, it doesn't really work out that well.But a much better option is this PBS Swiss bit block.Now, maybe this doesn't look like much, but it's much higher quality rigid holder, and it's a lot easier to get the bits in and out.They're perfectly engineered to hold these blades with just the right amount of tension.Each bit block holds 10 bits, so this set of four Phillips and five slotted fit here fine with an extra slot.All in, the Centrifix driver with the nine Phillips and slotted bits and the PBS Swiss bit holder cost around $60, which isn't cheap, but it is the ultimate bit driving experience if you don't want to carry around abag of individual screwdrivers.I like the setup so much that I recently picked up the other three sets to have a complete kit.
There's a nine piece security torque set for $20, a 10piece security hex for $20, and a set of three square for 13.I don't really need the security versions of these with the hole in them, but they don't offer standard ones, and these work just as well.To organize these, I bought a few more of the PBS Swiss bit blocks.The security hex set fills this one bit block here, and the security torque set only has nine, so I could put a 1/4in adapter in the last slot.To fit the square bits, I actually simplified this a bit to keep just a couple sizes.So, these are very similar as well as the small ones are really similar.So, we'll just shift these over.And now we have space for the three square heads.One nice feature of these bit blocks is there are these interlocking little tabs here.
So, you can line them up and slide them together and they'll lock.Now, these don't really lock together that well.So, if you really want to keep them that way, you might need to crazy glue them.All 29 bits plus the 1/4in adapter are now super neatly organized into this bit block.Let me show you what this looks like next to the tool check plus for comparison.And it's a little bit thicker.It's not nearly as wide.So now when I need to do something, I can just grab a blade out of here, throw it into the Centrafix, and I'm ready to go.
4. Ratchet Use and Tool Bag Storage
Using the Wera 838 R ratchet with the blades, keeping two dedicated drivers in a bag, and storing spare blades in the Veto TP-LC tool bag cubby for quick swaps.
I like to have the option of using a ratchet.And this new Vera 838 RM is really my favorite ratchet of all time because it's so fun to use.This locking wrap adapter does a good job of holding these blades in place.Now, there is a little bit of wiggle here, and that's true of all Vera ratchets, unfortunately, but when you're using it, it really isn't super noticeable because it's a ratchet.Now, the thing I really like about the 838 RA RM is this ring here.So, you can sit here and just turn it like this for really fine work or for starting the screw.But, this also sets the direction.So, if I want to loosen, I can just go that way.And now I'm loosening.If I want to tighten, I just do that.And now I'm tightening.There is a lock out in the center.
So, this becomes more like a standard driver, but you can see there's a decent amount of slop there.So, what I end up doing is leaving the Phillips number two in the Vera 838.And then I keep a large flathead screwdriver in the Centrafix.So, what I do is I keep these two drivers in my bag.So, now if I need to do something, I can just grab the driver and go.And if I need to switch the blades, I can do that really quickly.Now, one really cool thing I figured out is that this set of blades will fit into this little cubby in the top of the Veto TPLC tool bag that I have.So, by dropping it in the top, I can really quickly grab a blade and swap things out without needing to fiddle around too much.
5. Budget Option and Final Recommendations
Presenting the Vessel ball grip driver with inexpensive long Amazon bit sets as a budget alternative, comparing with the premium setup, and wrapping up with final recommendations.
Now, I know not everyone has $60 to spend on their screwdriver.If you're looking for a budget option, I found this Vessel ball grip driver.And it comes with three double-sided bits.There's a Phillips one and three, a positive drive two and three, and a 6 mm slotted with a Phillips number two on the other side.Of these three bits, the one with the Phillips number two and slotted is definitely my go-to.So, I just leave this stored in the handle.This doesn't have any sort of bit storage, so you're going to need to figure out what to do with these other two blades.Now, this thing just feels incredible in your hand.I love the weight distribution.The way this fits in the palm of your hand, and all the rubber grips that you get here really give you a lot of control.So, I think this is an excellent option.
And best of all, this only cost $13.These blades are actually a little bit longer at 110 mm or 4.3 in, but they do sit pretty deeply into the driver handle.And in case you're wondering, yes, you can use all of the VHA 90mimeter blades in here.And the nice thing is these sit in there pretty firmly.There's a teeny bit of wiggle, but it's very, very solid in here.You can combine the vessel handle with an inexpensive set of long bits like this Yakama set that I got for $13.It comes with 16 blades of 100 mm or 4-in bits that cover popular Phillips slotted, Torx, and hex sizes.They aren't amazing quality and needed to be washed to remove a ton of oil, but they're pretty solid.I did a ton of research trying to find inexpensive 4-in bit sets, and on Amazon, you'll find a bunch of them under a bunch of different brand names.
And the funny thing is, I think they're all coming from the exact same factory because on every single product listing, if you look at the Phillips number one, two, and three sizes, they're all labeled Phillips number two.What are the chances of that happening across multiple factories?I chose the 10 bits that I use most and added them to a PB Swiss holder, but I could have sprung for two to hold them all.These 4-in bits with the vessel driver handle is an awesome combination, and it only cost $26 or $31 with the bit block organizer.These together are an awesome combination and are just so much more usable than a multi-bit screwdriver like this Klein.So, there you have it.For the best driving experience, go with the VHA Centrafix and the VHA Power Blades.And for a budget option, go with any old set of 4-in blades off of Amazon with the Vessel driver.
Although I still love my Tool Check Plus and multi-bit drivers, you really cannot beat a dedicated driver handle and a set of long blades.Let me know if you found other high-quality blades or bit holders that you'd recommend down in the comments.Thanks for watching everyone.Till next time.